Powering Access Control Devices with 802.3bt PoE

              IOT_logo_19_winner           YELLOW-BIS-BICSIul-logo-png-transparent

 

Our new Tango PoE Driven Power Supply/Charger Series with Lithium Iron Phosphate Battery Backup is an industry game-changing power solution that allows 12VDC and 24VDC devices to be powered simultaneously via 802.3bt PoE input. Unlike Hi-PoE (60W), IEEE 802.3bt, also known as 4PPoE or 4-Pair PoE, uses all four pairs of wire in a structured cable to evenly distribute power. This new standard allows manufacturers of powered devices to design new products with power hungry features such as PTZ cameras w/ IR illuminators and heaters & blowers for harsh environments and more. 

There are several sources for PoE injectors that can supply 4PPoE for Tango, such as Altronix NetWay Midspans which are available in single port or multi-port options, which eliminates the need for multiple individual power injectors for larger projects.

 

Download Our FREE WhitepaperLearn More About Tango PoE Driven Power Kits    

 

Reduced Installation Costs

Traditional power supplies, hardwired with high voltage are typically used for the deployment of electrified locks. These power supplies generally take 115VAC/220VAC power input and reduce this to a 12VDC or 24VDC output. That single output is then connected to a distribution board where the electrified locks are connected. Most jurisdictions require that this power input be hardwired with a dedicated circuit. Due to the need for high voltage, a certified electrician must be used for this type of installation.

 

Watch our latest video on Tango and how it integrates with NetWayBT!

 

Security Integrators that are required to provide high voltage in their scope of work increases the cost of their installation. For instance, in large cities like Chicago, Boston, New York, Philadelphia, etc., electricians often have offices in the very same building the access control system is being installed, which limits options when contracting an electrician to do the work. Additionally, because of high voltage, the installation now requires dedicated conduit runs for the electrical as well as expensive large gauge copper and dedicated circuit breakers. After initial installation, regulatory compliance may be required to service the system. The new 802.3bt 4PPoE standard helps curtail the costs outlined above.

Traditional-vs-Tango_update

Powering Access Control Systems with 802.3bt

As previously stated, 4PPoE can deliver up to 90W of total power. At 100m from the power sourcing equipment, Tango1B 4PPoE Driven Power Supply/Charger provides 60W of power combined, 12VDC and 24VDC simultaneously. Total is determined after accounting for voltage drop on Cat5e. Shorter cable runs can provide up to 72W for use at the Tango1B. While there are adapters that convert PoE to 12VDC or 24VDC, the available power is limited. With up to 72W available, the flexibility to power an entire access control system with 4PPoE is a reality. This includes powering the access control panels, locks, readers and ancillary devices, while providing a battery charging circuit with a single Cat5e or higher cable. The Tango incorporates an 8-pin connector which allows for our stackable PDS8 power distribution board and ACMS8 access power controller to be mounted directly on top of the Tango board, where the 12VDC and 24VDC power is transferred to the distribution board via the 8-pin connector. This allows simultaneous 12VDC and 24VDC selectable outputs with visual indication of the specific voltage steered to each output.    

Below is an example of an 8 door access control deployment using Mercury boards, one of the most widely used platforms in access control, as the foundation of the system. Based on this example, you can see that 60W can potentially power
an entire 8 door access control system.

 

Powering an 8 Door Access Control System

QTY Device
Total Current Voltage

Watts

4 Mercury Boards 2150mA 12VDC 25.8W
8 Card Readers 440mA 12VDC 5.3W
8 Electric Strikes 1200mA 24VDC 28.8W

Total system draw: 59.9W*
*Calculations based on product specification sheets

T1MKTF4_wNetWay4BT_application-2Examining the benefits of Tango further provides a solution that also leverages best practice IT installations to conserve power and serve as a single point of maintenance for back-up batteries. For instance, the IT rack will likely house the Altronix brand midspan, which features a battery charging circuit. The IT rack may also have conditioned power and be supported by a back-up generator should there be a local AC power failure. When providing battery back-up for the PSE at the IT rack, using the Altronix RE2 rack mount battery enclosure with four 12V 7Ah batteries, the designer can eliminate the need for back-up batteries to be located in the field at each enclosure. This serves to eliminate the need to service batteries at multiple locations within the facility – saving time and labor for annual or routine battery maintenance.

 

Tango_PoE_Powered_Rack_Mount_Access_System_2

 

Additionally, without the need to utilize the on board battery charging circuit of the Tango1B, the designer saves an additional 10W of power which can be used for additional devices or as a factor of safety for system power.

Furthermore, it is not uncommon to utilize two power supplies based on the demands of an access control system. The designer may choose to deploy two Tango1B 4PPoE power supplies in a single enclosure to ensure that there is plenty of power for the system. Potentially using one Tango1B to provide power to all 12VDC devices and the second Tango1B to provide 24VDC. 

Using low voltage installation methods to power your access control system will eliminate the need for an electrician and associated costs such as permits, electrical cabling and dedicated conduit. The low voltage cable used for power can run in the same cable trays and paths as other network cabling along with access control cable. For service and maintenance, the lack of high voltage inside the enclosure eliminates the need for regulatory safety precautions. A key feature of the IEEE standard is that there is no voltage present on the cable from the PSE until it is plugged into a Powered Device and a handshake occurs. Unplugging the Ethernet cable from the PoE driven power supply is safe. Once the cable is plugged back in the handshake is performed with the power source and PoE is delivered to a powered device.

Make no mistake, today there is a demand for more power to support additional network connected devices. IEEE 802.3bt, also known as 4PPoE will be the catalyst that makes smart buildings a reality. Take full advantage of Tango and its characteristics to allow for more efficient, cost effective and safer installations.   

Altronix Tango1B is backed by a lifetime warranty.

Altronix Tango1B™

PoE driven Power Supply with Lithium Battery Backup

Tango1B_0719

Revolutionizing the power of access control, Tango1B is a PoE driven Power Supply/Charger delivering 12 and 24VDC simultaneously for deploying access control.

Powered by any 802.3bt PoE power source up to 90W, Tango1B harnesses the new IEEE standard. This industry game-changing solution eliminates the need for an electrician, dedicated conduit and wire runs – providing tremendous savings by using low-voltage installers and wiring methods.

Tango also provides battery charging for Lithium Iron Phosphate batteries (LiFePO4) adding to the systems ROI. The unique stackable design of the Tango1B allows for the use of compatible Altronix sub-assemblies, utilizing a single footprint – saving valuable enclosure space.

Download Our FREE Whitepaper

Getting-the-New-IEEE-802.3bt-to-Tango_Blog_Post

Getting the New IEEE 802.3bt to Tango

Read More